Tiktok:
instagram:
youtube:
  • 18201
    الترتيب العالمي
  • 4948
    ترتيب الدولة / المنطقة
  • 2.26M
    متابعون
  • 1.2K
    أشرطة فيديو
  • 38.88M
    الإعجابات
  • فيديو جديد
    16
  • متابعين جدد
    6.45K
  • طرق عرض جديدة
    2.32M
  • إعجابات جديدة
    33.91K
  • مراجعات جديدة
    418
  • مشاركة جديدة
    1.72K

Toolstoday  اتجاه البيانات (30 يوما)

Toolstoday التحليل الإحصائي (30 يوما)

Toolstoday فيديوهات ساخنة

Creating a self aligning glue joint using this Amana Tool 80 degree V Joint bit on the router table. The bit did a fantastic job cutting this making it a nearly seamless joint. This joint provides additional glue area strengthening the joint and is especially useful when making raised panels as the glue seam is much less noticeable when joined like this. All tools used are available from @toolstoday, be sure to check them out there. -- Amana Tool 80 degree V Joint bit, item no. 45790 JessEm Ultimate Excel II Router Table, item no. 09414 Woodpeckers in-DEXABLE Combo Square, item no. WP-CSQ-ST-20 JessEm Clear-Cut Stock Guides, item no. 04215 MicroJig GRR-Ripper push block, item no GR-100+
2.09M
26.05K
1.24%
52
173
1.13K
Using this giant 2-3/8" diameter bit to route a large chamfer on the bottom of this snowflake tray! The cut was all done in a single pass and the bit left a buttery smooth finish! I love the look this gives the tray from the side as the bottom disappears and almost makes it look like it's floating, like a real snowflake. The tools used in this video are available on our website and are listed below! -- Amana Tool 2-3/8" diameter 45 degree chamfer bit, item no. 49406 SawStop Inline Router Table, item no. RT-TGP
1.03M
7.81K
0.76%
1
26
175
Cutting a giant rabbet into a solid oak timber using the 5hp Powermatic shaper! I'm using a huge 5.9" diameter insert carbide cutter taking a 1.75" tall x 1" deep rabbet and the machine had plenty of power! My dust collection is woefully underpowered to keep up with the amount of chips being produced here, that will definitely need to be addressed soon! All tools used are listed below and are available from @toolstoday, be sure to check them out on our site! -- Powermatic 5hp PM2700 Shaper, item no. 1280101C Amana Tool 150mm D x 60mm CH Insert Carbide Rabbeting Cutter, item no. 61485 Wera Hex Plus L-Key Set Imperial, item no. 05022640001 MicroJig GRR-RIP block, item no. GB-1
835.58K
9.88K
1.18%
12
132
349
Rough cutting the nesting cutting boards using the templates we cut out on the laser. I chose to use contrasting wood here with white oak and walnut as I think the combination will look great together! The next step is to flush trim to the acrylic templates. All tools used are available from @toolstoday, be sure to check them out on our site! -- X-Fasten Double Sided Tape, item no. WO-5BMC-7UO9-1 Pica 3030 Pencil with white lead, item no. PC-30407 Timberline Carbide Tipped Forstner Bit Set, item no. 660-500 Rikon 14" Bandsaw 1.75hp, item no. 10-326
577.55K
3.55K
0.62%
1
19
114
What do you think of how this shop utility cart project turned out? If you're interested in making this for yourself, plans for the project are available on our website, item no. SHOPCART. All tools used in this video are also available from @toolstoday, be sure to check them out on our website! -- SawStop 5hp ICS Table Saw, item no. ICS51230-52 SawStop Large Sliding Table, item no. TSA-SA70 Grabo PRO 20 vacuum lifter, item no. GP-1Li-FB-1S Amana Tool 80T Double Sided Melamine Blade, item no. MSB1080 Stepcraft M.1400 CNC machine, item no. stepcraft_M1400 Amana Tool 1/8" Carbide Drill bit, item no. SCFD-100 Amana Tool 90 Degree Insert Carbide V-Bit, item no. RC-45711 Amana Tool 1/4" compression bit, item no. 46170-K Black Box Storm Vacuum, item no. BBV-SVP-2 Fein AMM700 MultiMaster Multi-Tool, item no. 71293662090 Festool Plunge Positioning Aid Base, item no. FS-203254 Festool Multi-Tool Blade, item no. FS-203336 Amana Tool 1/4" downcut flush trim bit, item no. 46297-K Amana Tool Mini 3/32" radius roundover bit, item no. MR0110 SawStop Inline Router Table, item no. RT-TGP MicroJig GRR-RIP Block, item no. GB-1 Festool CXS 18 Drill, item no. FS-576887 Festool CXS 12 Drill, item no. FS-576869 Amana Tool Adjustable No-Mar Carbide Tipped Countersink bit for Festool CENTROTEC System, item no. 55162 Amana Tool Adjustable No-Mar Carbide Tipped Countersink bit Hex Shank, item no. 55227 MicroJig MatchFit Dovetail Clamps, item no. DVC-538K2 Festool Hand Driver, item no. FS-200140 xTool F1 Laser, item no. XT-P5010200 xTool Desktop Smoke Purifier, item no. XT-P5010215 xTool Button Switch, item no. XT-P5010364 Festool ETSC 125 cordless sander, item no. FS-576822 Festool Soft Granat Abrasive Roll, item no. FS-497094 Festool Pocket Hand Sanding, item no. FS-583129
494.02K
8.01K
1.62%
4
115
390
Have you ever seen a 650lb machine move around this easily? The built in mobile base makes moving this machine around a dream yet perfectly stable once in place! The rest of the setup was quick and easy without needing to adjust anything to square up the machine and fence. We now have the first cutter installed and ready to test the machine out, stay tuned! All tools used are listed below and are available from @toolstoday, be sure to check them out on our site! -- Powermatic 5hp PM2700 Shaper, item no. 1280101C Wera 1/2" Zyklop Metric Ratchet Set, item no. 05003645001 Wera Hex Plus L-Key Set Imperial, item no. 05022640001
468.77K
10.15K
2.17%
57
171
972
The most important thing about making a tray like this with an engraved bottom, is to set your z-zero position from the same place with all tools. Then, when you set up your v-carve toolpath, set your start depth to the final depth you cut into the the tray. This ensures the v-bit carves the design correctly and will not contact the sides of the tray while doing rapid movements. The bottom of the snowflake catch all tray is now carved in and cut perfectly smooth! All tools used are available from @toolstoday, be sure to check them out on our site! -- Amana Tool 90 degree Insert Carbide V-Bit, item no. RC-45711 Vectric V-Carve Pro Design Software, item no. AVC308-2 i2R W.42 CNC machine, item no. i2RW42 AirWeights Complete 24"x48" vacuum workholding, item no. AWS-2448-SV1 -- RPM: 18,000 Feed Rate: 40ipm Plunge Rate: 20ipm
466.07K
1.67K
0.36%
1
11
60
What do you think of this piece? Making a heart catch all tray for Valentine's Day using Amana Tools on the Axiom Precision AR8 24"x48" CNC, all available from @toolstoday. Plans for this are available on our website, item number HCT. -- Matt started off flattening the piece using the RC-2255 2.5" 3 wing insert carbide flattening bit to make it perfectly flat before cutting the rest of it. -- RPM: 18,000 Feed Rate: 190ipm Plunge Rate: 95ipm Stepover: 80% Depth of cut: .1" Material: walnut -- He then used the 56126 3/16" Radius point roundover bit to add a roundover to each side, it's much easier to do on a CNC with pieces like this! -- RPM: 18,000 Feed Rate: 50ipm Plunge Rate: 25ipm Depth of Cut: .18" -- The bit was switched out for the 45984 3/4" diameter bowl bit to dish out the inside. There was a knot some Starbond super glue was used to fill it -- RPM: 18,000 Feed Rate: 40ipm Plunge Rate: 20ipm Depth per pass: .2" Stepover: 29% -- The 45771-K 30° Spektra coated engraving bit was used to engrave the bottom. -- RPM: 18,000 Feed Rate: 40ipm Plunge Rate: 20ipm Depth per pass: .1" -- Finally the 46416-K 1/4" downcut bit was used to cut the profile. It has a 1-1/8" cut height making it the perfect bit for this thicker piece. -- RPM: 18,000 Feed Rate: 80ipm Plunge Rate: 40ipm Depth per pass: .25" -- The MR0112 3/16" ball bearing mini roundover bit was used to roundover the bottom and trim the tabs. It was sanded with 220 grit paper and finish was applied. The piece is done and his wife loved it!
425.87K
3.98K
0.93%
7
40
280
Flawless tongue and groove edge banding using the Amana Tool 55468 60 degree edge banding set on the JessEm Ultimate Excel II router table all available on our website. These are the edges of a cart I'm making for the shop, they will take some abuse and this thick hardwood edge banding will keep the cart looking nice for many years to come! -- Amana Tool 60 Degree Edge Banding Set, item no. 55468 JessEm Clear Cut Stock Guides, item no. 04215 JessEm Ultimate Excel II Router Table, item no. 09414 MicroJig GRR-RIP Block, item no. GB-1 SawStop Table Saw, item no. PCS175-PFA30 Amana Tool 40T General Purpose, item no. PR1040C
406.57K
9.15K
2.25%
47
72
883
Mistakes happen, it's how you fix them that matters! The mistake I made here was in how I oriented the grain of the wood, I put the most likely part to chip out of the handle on straight grain rounding a corner. The chipout was inevitable and I should have oriented it differently on the piece. I save all of my offcuts from a project until the project is done and was able to find a perfect match so that you really can't even tell there was ever a mistake. All tools used are listed below and are available from @toolstoday, be sure to check them out on our site! -- Amana Tool 1/2" diameter Spektra coated Flush Trim Bit, item no. 46300-K SawStop Inline Router Table, item no. RT-TGP MicroJig GRR-RIP block, item no. GB-1 X-Fasten Double Sided Tape, item no. WO-5BMC-7UO9-1 1/4" Clear Cast Acrylic, item no. ACR-CLR Sjobergs Elite 1500 Workbench, item no. SJO-33246 Pica 3030 Pencil with white lead, item no. PC-30407 Woodpeckers Iron-Grip Small Parts Holder, item no. WP-IGSPH Rikon 14" Bandsaw 1.75hp, item no. 10-326 Titebond III Wood Glue, item no. 1414 Festool ETSC 125 Cordless Sander, item no. FS-576822 Festool Abrasive Roll Granat Soft 180 grit, item no. FS-497093
356.54K
4.28K
1.2%
1
33
48
Don't make this type of cut on a table saw! Making crosscut like this increases the risk of kickback significantly. Using a miter gauge is a really easy way to make this type of cut safe and more accurate, there are plenty of options out there, so pick what works for you! All tools used in this video are available from @toolstoday and are listed below. -- SawStop 1.75hp PCS Table Saw, item no. PCS175-TGP252 Amana Tool 80T Double Sided Melamine Blade, item no. MSB1080 JessEm Mite-R-Excel II Gauge, item no. 07150 Woodpeckers EXACT-90 Miter Gauge, item no. WP-E90 SawStop Crosscut Sliding Table, item no. TSA-SA48
343.94K
5.58K
1.62%
3
107
252
If you've tried to put a full 3/4" dado stack on your SawStop Table Saw, you know the problem, there's not enough shaft to install both the arbor washer and the arbor nut.  Leaving the washer off could provide uneven compression that could distort the blade and compromise cut quality.  Dado Nut merges the arbor washer and arbor nut into one integrated unit. The threads extend almost completely through the arbor washer and the nut is retained within the washer.  This may fit some other saws, in addition to SawStop, that utilize a 5/8"-12 tpi right-hand Acme threaded arbor. This as well as other Woodpeckers tools are available from @toolstoday, be sure to check them out on our site! -- Woodpeckers DADONUT-SS Dado Nut for SawStop Table Saws, item no WP-DADONUT-SS SawStop 1.75hp PCS Table Saw, item no. PCS175-TGP252
311.02K
3.11K
1%
3
15
94
Flush trimming the nesting cutting board to the acrylic template we made. This 1/2" flush trim bit slices through the wood like butter leaving an excellent surface quality on the wood! The tools used in this video are available on our website and are listed below! -- Amana Tool 1/2" diameter Spektra coated Flush Trim Bit, item no. 46300-K SawStop Inline Router Table, item no. RT-TGP MicroJig GRR-RIP block, item no. GB-1 X-Fasten Double Sided Tape, item no. WO-5BMC-7UO9-1 1/4" Clear Cast Acrylic, item no. ACR-CLR
294.64K
4.12K
1.4%
11
22
70
Engraving and cutting out some acrylic templates using the xTool P2 55w CO2 laser! The laser cut and engraved this acrylic beautifully and is now ready to be used to flush trim some wood to. All tools used are available from @toolstoday, be sure to check them out on our site! -- xTool P2 55w CO2 Laser xTool Smoke Purifier, item no. XT-P5010296 -- Engraving Power: 15% Speed: 500mm/s Lines Per cm: 200 -- Cutting Power: 100% Speed: 9mm/s Passes: 1
158.09K
3.18K
2.01%
8
43
249
Unboxing our new 5hp Powermatic Shaper! To say this machine is a beast is an understatement. Everything on this machine just screams heavy duty and quality down to all of the adjustment knobs on the machine. I cannot wait to show you this machine in action! All tools used are listed below and are available from @toolstoday, be sure to check them out on our site! -- Powermatic 5hp PM2700 Shaper, item no. 1280101C Wera 1/2" Zyklop Metric Ratchet Set, item no. 05003645001
134.03K
2.95K
2.2%
20
58
131
Making the first test cuts on this 5hp Powermatic shaper! This machine is an absolute beast, I'm taking a .75" tall x .375" deep dado here and I could hardly even tell it was cutting anything it was so smooth! This was just the first test cut, we have a lot more and much larger cuts planned for the machine, stay tuned! All tools used are listed below and are available from @toolstoday, be sure to check them out on our site! -- Powermatic 5hp PM2700 Shaper, item no. 1280101C Amana Tool 2.75" D x .75" CH Shaper Cutter, item no. 912 Wera Hex Plus L-Key Set Imperial, item no. 05022640001 MicroJig GRR-RIP block, item no. GB-1
129.91K
1.28K
0.98%
3
20
38
How satisfying is this?! I love v-carving @kingplastic Color Core on the Stepcraft M.1000 CNC machine using the Amana Tool RC-45711 90° insert carbide v-groove bit both available from @toolstoday. This bit cut right through it like butter! -- RPM: 14,000 Feed Rate: 40ipm Plunge Rate: 20ipm Max depth per pass: .25"
98.54K
1.03K
1.04%
1
8
61
Unboxing and assembling Smart Workstation Pro was quick and easy. I found this to be a quality workstation made of solid beech. This workstation has the ability to be set-on, clamped or bolted to most any work area. This adds a conventional work holding option to an unconventional workbench. The size and portability are a great addition to any workshop. All tools used are available on our website, be sure to check them out there. -- Sjobergs Smart Workstation Pro, item no. SJO-33309 Wera Zyklop Speed Ratchet Set, Item no. 05004016001
83.71K
1.04K
1.24%
1
11
117
Squaring up this oak timber on the Jet 8" helical head jointer! The jointer cut beautifully and made squaring up the material nice and easy, but the magnet toss took a few more times than normal 🤣 All tools used in the video are available from @toolstoday and are listed below! -- Jet 8" JWJ-8HH Helical Head Jointer, item no. 718250K Woodpeckers 642 Stainless Steel Square, item no. WP-SSSQ-06-19 -- #woodshop  #workshop  #woodworking
83.17K
1.38K
1.66%
0
14
32
يرجى الانضمام إلى مجموعة TikTok Inspiration على Facebook
سنشارك أحدث مقاطع الفيديو الإبداعية ويمكنك مناقشة أي أسئلة لديك مع الجميع!
TiktokSpy from IXSPY
أدوات رقمية للمؤثرين والوكالات والمعلنين والعلامات التجارية.
شركة خارجية مستقلة ، وليس موقع TikTok الرسمي.
Copyright@2021 ixspy.com. All Rights Reserved